ISO INTERNATIONAL. STANDARD. ISO. First edition. Safety of machinery — Permanent means of access to machinery —. Part 3. Why contractors should be paying attention to the EN Standard for ‘Safety of Machinery – Permanent means of access to machinery’ and. I.S. EN ISO Safety of machinery – Permanent means of access to machinery – Part 3: Stairs, stepladders and guard-rails (ISO.
|Published (Last):||11 October 2013|
|PDF File Size:||16.21 Mb|
|ePub File Size:||14.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Click to learn more. ENMinimum Gaps to Avoid Crushing Explaining the requirements of the 11422-3 for minimum gaps to prevent crushing. References are made to other subclauses that help in determining which type of access should be selected, but the point to note is that there must be good reasons for using any means of access other than those listed higher up the hierarchy.
It also notes that a self-closing gate should be used. Following on from the above, subclause 6. Clause 6, Verification of safety requirementsappears to contradict subclause 5. If an anti-climb device is fitted to a ladder, a written warning or audible signal is not adequate for access control. Clause 5Specific requirements of ladder systemsprovides extensive information relating to ladder design, including the profiles and dimensions of rungs round rungs are not permitted.
Stairs, stepladders and guard-rails. Annex ARequirements for the design of anti-climb devices, is normative and should, therefore, be complied with often an Annex to a standard is informative only. Documento Allegato Download Attachment. The edges of the handrail shall not have sharp ends, in order to prevent the risk of cutting or clothes getting entangled. Clause 7Specific requirements applicable to guard-railsstates that guard-rails shall be installed when the height of the possible fall exceeds mm, if the gap between the platform and machine structure exceeds mm or if the protection provided by the structure is not equivalent to a guard-rail.
Nevertheless, it would be prudent to verify the safety requirements either by calculation or testing. Remember that compliance with standards is not mandatory but is strongly recommended. When most people refer to stepladders they probably mean a short ladder with folding legs that enable it to be free-standing. Also, if the handrail is interrupted by a blank space, this should have a width between 75 mm and mm.
Click to learn more. The clause goes on to provide details of how to test guard-rails and the steps of a stair. Take the smart route to manage medical device compliance. It specifies minimum requirements that also apply when 14122- same means of access is required as the part of the building or civil construction e.
Annex B informative illustrates the main dimensions of a fixed ladder equipped with a safety cage.
Guidelines for the European Standard EN ISO
Clause 8Verification of safety requirementsgives a choice of testing or calculation. However, the same subclause states that the minimum height of the guard-rail shall be mm, so it appears that the former may be a fn error and the height of the handrail should be greater than or equal to mm. Note that subclause 6. Means of access, as with guarding, sn to control access to machine-related hazards under different circumstances — such as operation, cleaning and maintenance — and should not themselves introduce significant new risks.
Our KeeLine fall protection solution provides fall arrest where guardrails are not suitable. Please download Chrome or Firefox or view our browser tips.
Earlier this White Paper mentioned the need to prevent unauthorised access. Permanent means of access to machinery. Visit our w… twitter. With a heavy duty PVC base weighing 25kg, our Kee Mark system is protected even during severe weather conditions. Clause 6Specific requirements applicable to step laddersprovides similar details to those in Clause 5.
White Paper 7 – BS EN ISO | Free Downloads | Procter Machine Safety
View our installation page to see how our products can be applied ow. Annex A relates to methods for determining slip resistance and starts by stating that no international standard currently exists. Readers who are concerned about what changes might occur in relation to standards once the UK leaves the European Union can rest assured that it is unlikely that there will be any change here 14122-33 BS EN ISO is equivalent to the international standard and it is all but inconceivable that the UK would cease to use this.
Updated standard requirements The system should incorporate a knee rail that is mm from the top rail, and a lower bottom rail that is no more fn mm from the floor level. Furthermore, a permanent means of access can prove to be very cost-effective compared with the cost eb erecting scaffolding on multiple occasions. Annex A relates to methods for determining slip resistance and starts by stating that no international standard currently exists.
Remember that compliance with standards is not mandatory but is strongly recommended. Clause 7Specific requirements applicable to guard-railsstates that guard-rails shall be installed when the height of the possible fall exceeds mm, if the gap between the platform and machine structure exceeds mm eh if the protection provided by the structure is not equivalent to a guard-rail.
BS EN ISO 14122-3:2016
This website is best 1412-23 with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. In other words, when designing and specifying means of access, consideration should be given to preventing unauthorised access.
The rules for the construction of permanent edge protection systems listed below are 141223 primarily from EN ISO The faster, easier way to work with standards.
Our site requires cookies to function, click here for more information Ok, thank you.