DECODER HT12D PDF

HT12D is a series decoder IC for remote control applications manufactured by Holtek. It is commonly used for radio frequency (RF) applications. Download. Make a RF Transmitter and Receiver With HT12E & HT12D: Would you like to With the help of our friends HT12E (ENCODER) and HT12D (DECODER) and a. The HT12D is a 2^12 decoder in 18 pin DIP package. This decoder is a series of CMOS LSIs for remote control system applications. It is paired with Holtek’s.

Author: Moogurg Faejas
Country: Senegal
Language: English (Spanish)
Genre: Career
Published (Last): 13 April 2005
Pages: 58
PDF File Size: 9.27 Mb
ePub File Size: 14.4 Mb
ISBN: 625-4-33529-126-9
Downloads: 58043
Price: Free* [*Free Regsitration Required]
Uploader: Shakasa

Virgin Galactic — Commercial Space Flight. This oscillator can be used by connecting these two pins through a 1M Resistor. They can also be connected to LED to physically view the received data.

These are the 8-bit address bits, which is used to protect your data. This oscillator can be used by connecting these two pins through a 1M Resistor 17 Valid Transmission VT This decodsr will go high when a data is ht12x.

HT12D Decoder IC | HT12D Datasheet | Pin Diagram

HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Choosing Motor For Robots. Submitted by admin on 27 October These two ICs together form an Encoder and Decoder pair. A valid transmission in indicated by htt12d high signal at VT pin. This high-density System-in-Package SiP integrates controller, power switches, and support components.

HT12E & HT12D ENCODER DECODER IC

The serial input data is compared with the local addresses three times continuously. A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. In simple terms, HT12D converts the serial input into parallel outputs.

  BIBIANA Y SU MUNDO JOSE LUIS OLAIZOLA PDF

The input data code is decoded when no error or unmatched codes are found. Supply voltage; 5V 2. This pin will go high when a data is received. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits. TL — Programmable Reference Voltage. This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc.

Interface GPS with Arduino. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Choosing Battery for Robots. Decoser any valid data is received they can be bt12d from these four pins. It is very important that your Decoder should have the same address of that of the encoder. SPI Module of Arduino. Valid transmission; active high.

Arduino based GPS receiver. The data on 4 bit latch type output pins remain unchanged until new is received. Interface SD Card with Arduino. The IC has a built in oscillator.

They are paired with 2 12 series of encoders. The Encoded 12 bit output data obtained from HT12E has to htt12d given here. This pin powers the IC should use only 5V.

It is not mandatory to use it.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

Connected to the Ground of circuit. To know dedoder a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

  BSNL JTO NOTIFICATION 2009 PDF

It is mainly provided to interface RF and infrared circuits. If you want security you can connect any of the 8 pins to 5V to make it high. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

HT12D Decoder IC

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will decpder best suited for you. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Skip to main content. What is Web Browser.

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.