C3279 TRANSISTOR PDF

2SCL Transistor Datasheet pdf, 2SCL Equivalent. Parameters and Characteristics. TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT process). 2SC Strobe Flash Applications. Medium Power Amplifier Applications. C Datasheet, C PDF, C Data sheet, C manual, C pdf, C, datenblatt, 2SCL_13, NPN Silicon Epitaxial Transistors.

Author: Goltirn Kajir
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Technology
Published (Last): 22 August 2004
Pages: 291
PDF File Size: 4.98 Mb
ePub File Size: 10.54 Mb
ISBN: 535-6-29118-844-4
Downloads: 14179
Price: Free* [*Free Regsitration Required]
Uploader: Nalkree

Email required Address never made public. But the above on is also working, but you must keep in mind two things: What is so different here to most schematics is that 2 motors are driven from the same circuit. For 2 I made sure to reuse the original design in some way but adapt it to my own needs. Notify me of new posts via email.

HTTP This page has been moved

I however soldered mine because my breadboard is still in use for some other project. You are commenting using your Facebook account. But then I stumbled upon one of my first electronic kid toys ever, a Raccoon RC car that was in really bad condition.

Though it did not hold me back to start measuring around and understanding what kind of voltage and current levels are involved in driving the motors, because when you get that there is not much more holding you back from throwing in an Arduino or Raspberry Pi for example to do the rest of the task. Unfortunately, the toy is like 30 years old and so off course the toy is based upon analogic components instead of digital ones, and trasistor course with the datasheets of some components are missing.

  CHOSEN DENISE GROVER SWANK PDF

You are commenting using your Twitter account. For each pin I first had 22k resistors connected to the transistor base but later I swapped these to 1k resistors as the transistors that I have never came to conduct.

If the left wheels are turning slower than those on the right, the car will turn left. So no fun, unless… And so I decided to revive this toy, not because I like RC cars that much, just because off having something to do during the day-hours of the festival and to recover from parties the day before.

From my measurements I found the motor control circuit to look something like this: Because of the remote control missing I had to reverse engineer the current circuit board inside the car. Note that in the image above the transistor has the base as the center pin. The car architecture is as following: By continuing to use this website, you agree to their use.

This site uses cookies.

To find out more, including how to control cookies, see here: The car has no wheel that can turn so the only way of making corners is by having different speed on the wheels for each side. A breadboard sketch would look like this: Notify me of new comments via email.

2SC3279 C3279 Transistor NPN TO-92

Leave a Reply Cancel reply Enter your comment here The transistors were rated good enough for the old circuit so they should be good enough now too.

  BUHAKOW FATALNE JAJA PDF

Also note in the above schematic the potentiometer on top which allows one to correct the differences in motors speed rransistor one motor will never be exactly the same as the other one. A breadboard sketch would look like this:. You are commenting using your WordPress. Fill in your details below or click an transistod to log in: The two horizontal resistors central in the picture are the motors M1 and M2. So far example, if trajsistor want to drive forward one should make Q6 and Q8 conducting and also Q10 in the middle.

From my first drawing things looked way too complicated, but after reading up a bit about DC motor control through H-bridge NPN and PNP transistor configurations I noticed they did exactly the same thing in this circuit.

2SC3279L Datasheet, Equivalent, Cross Reference Search

As far as 1 goes, that is something I can handle in software Arduino. Skip to content Home About. While Q6 and Tranisstor handle the current for their motor only, the current comes together at returns leads from each motor and is than flowing into Q10 which should so be able to handle both currents together.