ddx – read user manual online or download in PDF format. Pages in total: 12 . This page contains information about the User Manual for the DDX from Behringer. Music Mixer Behringer ddx different pdf manuals and documents on this page.
|Published (Last):||3 January 2016|
|PDF File Size:||2.95 Mb|
|ePub File Size:||15.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
To reduce the risk of electric shock, do not remove the cover or rear. No user serviceable parts inside; refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure—voltage that may be sufficient to It is one of my most pleasant tasks to write this letter to you, Ex factory, the analog inputs are assigned to channels It complies with all applicable safety standards.
Blown fuses must always be replaced by fuses of the same type and rating. Channel level meter Each fader has a channel level meter assigned to it. Depending on the active fader vehringer, this meter reads the pre-fader or pre- processing levels inputsor the post-fader output level outputs such as bus, aux and Manjal.
Normally, the channel meter follows the fader bank settings and reads the level of its associated fader. Display with control elements Many functions of your mixing console are controlled via the display, including the general setup, channel processing and the built-in effects processors. By pressing a switch in the switch block, you can display whole groups of associated menu dd3216.
Each group has a menu bar on the upper right side, and each single menu page has a tab along the top left part of the display. Groups can span more than one fader menu page. The low-cut filter has only one frequency parameter, which controls the frequency at which the signal is cut by 3 dB cutoff frequency. All frequencies below that value are attenuated with a slope dd3x216 12 dB per octave.
So, when you select a frequency of Hz, it will behringef cut by 3 dB; The lower the threshold, the more the signal is affected. Signals below the threshold, however, remain unaffected. These busses can be used for a wide variety of applications, e. The aux and FX sends are adjusted with the channel controllers and the display.
Using the AUX and FX switches in the left switch block you can assign one common aux or FX send to the channel controllers of channels or When you press the AUX and FX switches in the left switch block, the AUX and FX send page is displayed, providing you with an overview of all sends and masters, including their pre and post-fader settings. These four multi-effects processors offer 26 different groups of first-class effects, including such standard effects as reverb, chorus or delay, but also unconventional effects such as a ring modulator, plus various filter and lo-fi effects.
Decay 0 to 10 s The Decay parameter controls the duration of the reverb tail, which is the time needed for the level of the reverb tail to drop to dB. PreDelay 0 to ms This parameter controls the delay in msuntil early reflections and reverb tail can be heard. Diffusion 0 to 20 The Diffusion parameter allows you mabual edit the density of the reverb tail. Size 1 to 50 Size determines the room size with regard to the early reflections. The signal is also fed back.
The resulting phase shift is called comb filter effect. Mod Delay 5 to ms Mod Delay controls the delay of the modulated signal. NR-Response 20 to ms This parameter controls the response time of the gate.
Any changes made here will be stored until you power off your DDX or change them next time you use the copy function. The inputs are assigned in behringef of eight, which enhances the flexibility of your DDX considerably. This input is fitted with a sample rate converter that allows you to feed in digital signals with sample rates between 32 and 50 kHz. What is more, your DDX stores the last snapshot used and recalls it after power-up.
These files can be used as backups or to transfer data from one DDX to another.
Copying a file of this type to the middle window internal files will delete all DDX settings, and load a new operating system see chapter Snapshots can also be switched over by means of program change commands see chapter Simply start the multi-track recorder and mix, and the DDX will play back exactly what has been recorded before, or will record what is being added.
If the switch is disabled, the DDX is in absolute mode, i. The flash memory of the console stores one automation file. Adjustments can always be made later on, but the mixer behringsr use the status of the controls as the basis for the new mix when automation is turned on. The built-in clock of your DDX Behriinger the appropriate checkboxes to enable these functions. Any additional DTRS wordclock code via the sync port of the master recorder, behringr are configured as slaves.
The packaging of your DDX contains two 19″ rack mounts for installation on the side panels of the console. Before you can attach the rack mounts to the DDX, you need to remove the screws holding the left and right side panels. bwhringer
Behringer DDX3216 Musical Instrument User Manual
However, you can also use two-conductor shielded cables e. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated. Page of 56 Go. Table of Contents Add to my manuals Add. Ultimate 5-channel digital dj mixer with sampler, 4 fx sections, dual bpm counters and midi 30 pages. Ultimate 5-channel digital dj mixer with sampler, 4 fx sections, dual bpm counters and midi 21 pages.
Professional 5-channel dj mixer with advanced digital effects and bpm counter 10 pages.
Behringer – DDX – User Manual
Professional 5-channel dj mixer with advanced digital effects and bpm counter 11 pages. Professional dj mixer with a total of 10 stereo sources on 5 dual-input channels 29 pages.
Professional dj mixer with a total of 10 stereo sources on 5 dual-input channels 22 pages. Professional dj mixer with a total of 4 stereo sources on 2 dual-input channels 19 pages.
Table Of Contents 1.
Introduction Seeing is believing! Main Mix Channel level meter Each fader has a channel level meter assigned to it. Channel Control Bank Groups can span more than one fader menu page. Auto mation Bank 2. Channel Processing Switches 6 ebhringer cuts the msnual by half. Dynamics Processing The low-cut filter has only one frequency parameter, which controls the frequency at which the benringer is cut by 3 dB cutoff frequency.
Dynamics Library Menu Page The lower the threshold, the more the signal is affected. Page 23 The aux and FX sends are adjusted with the channel controllers and the display. Small Hall Decay 0 to 10 s The Decay parameter controls behrinegr duration of the reverb tail, which is the time needed for the level of the reverb tail to drop to dB.
Phaser LFO Speed 0. Groups, Pairs And Copy Functions 7. Pair Function turn to select; press to change. File Management What is more, your DDX stores the last snapshot used and recalls it after power-up.
Dynamic Automation Simply start the multi-track recorder and mix, and the DDX will play back exactly what has been recorded before, or will record what is being added. Perfecting A Mix Adjustments can always be made later on, ddz3216 the mixer will use the status of the controls as the basis for the new mix when automation is turned on. Setup 32 and 50 kHz, regardless of whether or not these signals are in sync with the console. The Ddx In Live Applications including equalization and effects with the faders of channels Installation The packaging of your DDX contains two 19″ rack mounts for installation behrinyer the side panels of the console.
Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.
To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?