View Catalogue AP-V80 Series Durable Multi-Fluid Digital Pressure Sensors Catalogue. Two Digital Display Pressure Sensor Amplifier; AP-V80W Series. A rugged and compact sensor head has been assembled using a single-piece stainless steel pressure element and housing. The AP-V80W Series can be used. Cheap sensor mouse, Buy Quality sensor clock directly from China sensor engine Suppliers: KEYENCE pressure sensor AP-V80W Enjoy ✓Free Shipping.
|Published (Last):||24 July 2006|
|PDF File Size:||5.41 Mb|
|ePub File Size:||10.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Durable Multi-Fluid Digital Pressure Sensors
The mode can be switched between on and off by pressing the or button. Leakage test 20 20 Zero-shift input Zero-shift input — 0. Output 2 Detects the pressure value of the H higher pressure value side.
Finally, lock the root of the connector covers with the connector security rings. The hysteresis margin is changeable in all detection modes. Use a pair of pliers or similar tool to press them together. P2 Hys P1 Hys button. Do not use the product for detecting the flammable gasses or liquids.
The lower part indicates the reference value of zero-shift. F-2 Double window 8v0w This mode is used to judge whether the pressure value is within the range between the upper limit wp lower limit values at the detection point.
Output 2 When the Turns on when f80w pressure exceeds the setting value P2. The peak bottom hold is activated when the pressure value exceeds lowers the setting value until the pressure value exceeds lowers the setting value again. The lower part indicates the reference value of shift setting. It turns off if the hysteresis margin is subtracted from the setting value P2. Output 2 Turns on when the pressure exceeds the setting value P2.
However, the pressure value at this time is detected without being influenced by the display shift 0 caused by the zero-shift input. It is valid sp when the zero-shift is turned on.
Durable Multi-Fluid Digital Pressure Sensors – AP-V80 series | KEYENCE America
The output indicator and the alarm indicator function normally. The lowest pressure value aap the pressure has v8w0 below the setting value remains displayed. The detection points can be switched by turning the external input on or off. Cut the cable to an appropriate length About About 16 mm and strip away about 16 mm of the 16 mm outermost insulation.
Documents Flashcards Grammar checker. Output 1 When the Turns on when the pressure exceeds the setting value B1.
Do not use the product in an environment with flammable gas or something similar. It turns off if the external input is turned on hysteresis margin is subtracted from the setting value B2.
AP-V80W Series Pressure Sensor Heads : AP-V80 series | KEYENCE International Belgium
Output 2 When the Turns on when the pressure exceeds the setting value B2. Zp value can be set in the same matrix as that of the display resolution.
Eco mode mW mA max. It turns on when the pressure difference H-L goes lower than the setting value P1. If incompletely inserted, the connector can be easily disconnected. Do not use a load that exceeds the allowable limit. Press the button to reset to the default settings, and the screen returns to the head selection screen. Unless stated otherwise herein, the Products should not be used internally in humans, for Solution human transportation, as safety devices or fail-safe systems.
Ao a hold mode by pressing the Press once. The pressure value in the H side is described as H, and the one in the G80w side is described as L. Caulking machine Auto peak hold Setting value The current value is displayed until the pressure lowers the setting value. Select indicator 2 as a setting a. Zero-shift This is a function that sets the pressure at that time pa to zero by inputting an external signal.
The pressure difference during the zero-shift input is displayed as zero in the current setting value while the zero-shift input is turned on. Select indicator H as a setting value. You can check the abnormal value of air pressure afterward. Output 2 When the Detects the pressure value of H higher pressure value side.
Residual voltage 1 V max. The value that has undergone atmospheric pressure correction is stored even if the power is turned off. Check the load and adjust it to the rated range.
F-1 General-purpose mode This is a mode where the pressure detection point can be specified at desired two points. High-speed v80q Setting value can be configured by pressing the and buttons. F-3 Leakage test zp mode This is a mode suitable for a leakage test using a master workpiece. The sensor inserted in the H side detects the higher pressure, and the one inserted in the V800w side detects the lower pressure. Detection is not possible when it is set backward.
It turns off if the external input is turned off hysteresis margin is subtracted from the setting value P2. The hysteresis margin is changeable in all modes setting.
Confirm the sanitation standards required for facilities. To dismount the sensor, raise the zp body in the direction of the arrow 3 while pushing the main body in the direction of the arrow 1. Perform the desired change in the mode setting.
Note that no output is made during this period.