Buy Analogue input module,IE8 mA IE8. Browse our Mfr. Part No. IE8; Brand Allen Bradley I/O,module,Flex User Manual. Legislation. (Cat. No. IE8 Series B). 4. 1. 3. 2. 5. 6. 7. Module Installation. This module mounts on a terminal base unit. 1. the module. Installation Instructions. User manual • Read online or download PDF • Rockwell Automation IE4XOE2,IE8,OE4,D FLEX I/O ANALOG MODULE User.
|Published (Last):||17 May 2008|
|PDF File Size:||12.97 Mb|
|ePub File Size:||17.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
IE8 & OE4 User Manual_百度文库
Bit 00 corresponds to input 0, bit 01 corresponds to input 1, bit 02 corresponds to input 2, and bit 03 corresponds to input 3. If you do not, refer to the appropriate programming and operations manual before you attempt to program your modules. You can reduce the input words to 8 by not using the underrange settings set in word 9.
Refer to the following table for recommended terminal base units that you can use for each module. Rotate the terminal base onto the DIN rail with the top of the rail hooked under the lip on the rear of the terminal base. In this example, we want the 4 20mA input data to mqnual 32 to degrees in the PLC 5. Mapping Data into the Image Table. The second compute instruction has a final destination of an integer location. Not used – set to 0. The adapter is capable of addressing eight modules.
Total 1794–ie8 draw through the terminal base unit is limited to 10A. Power Up bit – included in series B modules only.
Analog module wiring separate from discrete wiring. Connecting Wiring for the Analog Modules. If the adapter does not establish communication with the module, cycle power to the adapter. In the above example: Features of your Analog Modules. Safe State Value Selection You can select the analog values that your output module will maintain in the event of a network communication error.
Thereafter, the program continuously performs read block transfers to configure the module. In particular, you must know how to program block transfers. Safe State Value Selection.
You must know and understand how DeviceNet Manager works in order to add a device to the network. The module is configured manal a group of data table words that are transferred to the module using a block transfer write instruction. A removable label provides space for writing individual designations per your application. You can disable BTRs, or add interlocks to prevent writes if desired.
Chapter Summary In this chapter, you learned how to program your programmable controller. Channel 2 analog data sign bit.
Drill the necessary holes for the 6 self-tapping manuall screws.
Since there are many variables and requirements associated with any particular installation, Allen-Bradley does not assume responsibility or liability to include intellectual property liability 1794-i8 actual use based upon the examples shown in this publication.
Channel 2 Safe State analog value – 12 bit left justified two’s complement number; unused lower bits are zero; 4 20mA uses all 16 bits. Bit 00 corresponds to output 0, bit 01 corresponds to output 1. For example, the following binary number is equal to decimal Do not daisy chain power or ground from an analog terminal base unit to any ac or dc discrete module terminal base unit.
Mapping Data for the Analog Modules.
Hold the adapter 2 at a slight angle and engage the top of the mounting plate in the indention on the rear of the adapter module. For example, for the 8 input analog module, you have 9 input words, and 6 manaul words.
Scripting must be enabled to use this site.
Likewise, you can reduce the write words to 0, thus eliminating the configuration setting and unused words. The processor’s user program initiates the request to transfer data from the input module to the processor.
This bit is set to 1 when all bits in the configuration register write word amnual are 0 unconfigured state. Refer to Appendix B for more information. Use the mounting kit Cat.
Underrange bits U for individual channels 4 20mA current input only – Bit 00 corresponds to input channel 0, bit 01 corresponds to input channel 1, and so on. Calculate the manhal requirements mwnual all modules in each chassis. The analog modules have selectable ranges as shown in the table below: This bit is set 1 when the node address switch setting has been changed since power up.
Then it initiates a block transfer write to configure the module and send data val ues Thereafter, the program continuously performs read block transfers and write block transfers. Refer to range selection above. Word 7 Chapter Summary In this chapter you learned how to configure your module’s features and enter your data. We recommend you frequently backup your application programs on appropriate storage medium to avoid possible data loss.
The number is positive if the sign bit is 0 and negative if manua sign bit is 1. This software tool can be connected to the adapter via the DeviceNet network.